Announcement

Collapse
No announcement yet.

SV-1 voice key and eprime

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Hisham
    replied
    Try with SuperLab 4.0 as I mentioned earlier, it'll handle it better.

    Leave a comment:


  • dbiun
    replied
    Xidon starts up, and when it does the autocheck I get an error message:

    Debug Error
    in Xidon.exe

    Run-Time Check Failure 2 - Stack around the variable CBUFF was corrupted

    IF I press ignore, then it comes up with a prompt that says
    Xidon detected an XID device, but it is either unsupported by this version of Xidon or the firmware is out of date.

    Leave a comment:


  • Hisham
    replied
    if you have been using SV-1 with E-Prime, Xidon isn't smart enough to convert SV-1 from E-Prime mode back to XID mode, but SuperLab 4.0 is. You can download the 30-day trial and use it to convert SV-1 back to XID mode.

    Note: when in E-Prime mode, SV-1 emulates the PST Serial Response Box. In doing so, it sends 800 or 1600 bytes per second to the computer, making it difficult for the computer to communicate with SV-1. You may need to try several times before SuperLab 4.0 tells you that it found an SV-1.

    Leave a comment:


  • dbiun
    replied
    So what do we do if Xidon can't find the voice key?

    Leave a comment:


  • Hisham
    replied
    SV-1 Firmware v1.4

    Here's version 1.4 attached that sends a 0x20 -- as it should.
    Attached Files

    Leave a comment:


  • Hisham
    replied
    You are right. I was off by one bit. Our RB Series response pads already send 0x20 to emulate a voice key when a key is pressed. I'll get back to you with an update soon.

    Leave a comment:


  • christoph
    replied
    Hi! I now installed the new firmware on our voice keys and I can confirm that they are now sending 0x40 when the voice key is triggered in PST mode. I can also successfully tried to use them in eprime. That is great! Thanks a lot for this fix!

    However, I noticed one minor issue: PST counts bits from 1 and not from 0. So, the PST SR Box is sending 0x20 and not 0x40 when the voice key is triggered. 0x40 is used for the screen refresh detector of the SR Box. In order to provide full compatibility with the SR Box it might be advisable to send 0x20 instead of 0x40 as well.

    Leave a comment:


  • Hisham
    replied
    I've attached the new version of the firmware. You'll need the Xidon program; SV-1 must be in XID mode. I look forward to your feedback. The new firmware sends 0x40 when voice key is detected.
    Last edited by Hisham; June 23rd, 2009, 03:23 PM. Reason: removed attachment

    Leave a comment:


  • christoph
    replied
    Hisham, I am glad to hear that you finally could replicate our problems. When do you reckon will the fix be available? I am asking because one of our researchers wants to start testing at the beginning of July. If the bugfix takes longer I need to find her an interim solution. I suppose we can update the voice keys ourselves (the are 2G ones)?

    Leave a comment:


  • Hisham
    replied
    Christoph, I can confirm that it's a bug in SV-1's firmware. I have opened a report in our case tracking system and we should have a bug fix available soon.

    Leave a comment:


  • christoph
    started a topic SV-1 voice key and eprime

    SV-1 voice key and eprime

    Hi,

    our SV-1 voice keys are not working with eprime. Checking the firmware version on the voice keys with Xidon revealed that the are running version 1.1. This version is known not to work with eprime.

    Does anyone know where I can download the current version 1.3 of the SV-1 firmware?

    Thank you!
Working...
X